1
EPA/540/S-97/502
April 1997
United States
Environmental Protection
Agency
Office of Solid Waste
and Emergency
Response
Office of
Research and
Development
Ground Water Issue
How Heat Can Enhance In-situ Soil and Aquifer Remediation:
Important Chemical Properties and Guidance on
Choosing the Appropriate Technique
Superfund Technology Support Center for Ground Water
National Risk Management Research Laboratory
Subsurface Protection and Remediation Division
Robert S. Kerr Environmental Research Center
Ada, Oklahoma
*
National Risk Management Research Laboratory, U.S. EPA
Eva L. Davis *
Technology Innovation Office
Office of Solid Waste and Emergency
Response, US EPA, Washington, DC
Walter W. Kovalick, Jr., Ph.D.
Director
Background
The EPA Regional Ground Water Forum is a group of EPA
professionals representing Regional Superfund and Resource
Conservation and Recovery Act (RCRA) Offices, committed to
the identification and resolution of ground-water issues impact-
ing the remediation of Superfund and RCRA sites. Innovative
technologies for subsurface remediation, including in-situ tech-
niques based on heating the subsurface to enhance the recovery
of organic contaminants, are being evaluated more often for
specific sites as the limitations to the conventionally-used tech-
niques are recognized. The purpose of this Issue Paper and the
three companion Issue Papers (Davis, 1997a, b, c) is to provide
to those involved in assessing remediation technologies some
basic information on the thermal remediation techniques. In
order to understand how heat can enhance a remediation
process, it is essential to understand the properties of organic
contaminants that affect their recovery. Thus, this Issue Paper
contains in-depth information on the properties of some common
organic contaminants which can affect their movement in and
recovery from the subsurface, as well as information on how
these properties are affected by temperature. Then, some basic
information on which of the heat-based remediation techniques
may be most appropriate for the subsurface conditions and the
contaminants is also provided, as well as a comparison of the
heat-based techniques to other in-situ remediation techniques.
The three companion Issue Papers have been written to provide
an explanation of how each of the three general types of
processes (steam or hot air injection, electrical heating, and hot
water injection) works, as well as preliminary information on the
design of a system and some estimates of the expected costs.
Thus, once the ground-water remediation specialist has deter-
mined which of the thermal methods may be appropriate for a
particular site, the Issue Paper on that method may be consulted
for more detailed information on how the process may be
applied.
Introduction
Thermal treatment is a common and proven technology for the
remediation of contaminated soils (Lighty et al., 1990), but in the
past thermal treatment has been applied mainly to soils that have
been excavated and are then incinerated to release and/or
destroy the contaminants. However, excavation of contami-
nated soils is not always practical and can be extremely costly
when the contamination occurs at great depths or covers a large
area. Excavation also increases the risk of exposure to and
further dispersion of the contaminants during material handling
steps (Dev et al., 1989;
Superfund Report
, August 10, 1994).
Heat-based in-situ remediation methods can be used in many
places where excavation is not possible, such as under and
around surface structures, and around empty underground
tanks and utilities (U.S. EPA, 1995d). In many instances, heat-
based in-situ remediation techniques have been found to be cost
effective compared to the excavation and incineration option or
other remediation techniques (Dev et al., 1989; Basile and
Smith, 1994; Yow et al., 1995).
2
The most commonly used remediation technique for the recov-
ery of organic contaminants from ground water has been pump-
and-treat, which recovers contaminants dissolved in the aque-
ous phase. Vacuum extraction (also called soil venting) is
quickly becoming popular for removal of volatile organic con-
taminants from the unsaturated zone in the gaseous phase (Ho
and Udell, 1992; Shah et al., 1995). Both of these techniques
can, in the initial remediation phase, rapidly recover contami-
nants at concentrations approximately equal to the solubility limit
(pump-and-treat), or the maximum gas phase concentration of
the contaminant (vacuum extraction). The maximum gas phase
concentration will depend on whether the contaminant is present
as a free phase or as a solute in the aqueous phase. During this
initial phase, large amounts of the contaminants may be re-
moved. The second phase of the remediation, however, is
characterized by rapidly declining contaminant concentration in
the effluent as the rate of mass transfer into the flowing phase
controls the rate of removal. The third phase of the remediation
is characterized by a
tailing
in the effluent of low contaminant
concentrations. However, low effluent concentrations may not
be a reliable indication of low contaminant levels remaining in the
subsurface. Diffusion of contaminants from less-permeable
areas into the regions where flow is occurring or the slow
desorption of contaminants from the soil surface may control
contaminant removal during this phase, and termination of the
extraction process before these processes are complete may
lead to significant rebounding of the ground water and/or soil air
concentrations (Mackay and Cherry, 1989).
Thus, the rate-limiting properties of the systems are different in
each of the three phases of the remediation: in the first phase,
the solubility of the contaminant in the aqueous phase (pump-
and-treat) or its maximum gas phase concentration (vacuum
extraction); in the second phase, it is the mass transfer step, i.e,
dissolution into the aqueous phase (pump-and-treat), or vapor-
ization (vacuum extraction); and, during the third phase, it is
diffusion from low permeability areas or the desorption rate
(Shah et al., 1995).
Instances of soil and aquifer contamination by oily contaminants
such as automatic transmission fluid (Abdul et al., 1990), coal tar
(Gerencher et al., 1992) and creosote (Johnson, 1994) have
been documented. Contaminants such as these oils are prac-
tically insoluble in water and have essentially no vapor pressure.
Thus, they will be present in the subsurface as a nonaqueous
phase liquid and must be recovered as such. The recovery of
these types of products is often limited by slow movement to
recovery wells caused by their high viscosity and the significant
residual saturation left behind. Heat-based in-situ remediation
techniques which overcome or lessen the influence of each of
these limitations to the recovery of organic contaminants have
been developed and are being field tested.
Properties of the Contaminants
Organic contaminants in the subsurface can be present as a
separate nonaqueous phase liquid, dissolved in the aqueous
phase, in the vapor phase in the soil gas, partitioned into the soil
organic matter, or adsorbed onto the solid mineral phase. The
relative amount of the contaminant in each of these phases is
determined largely by the properties of the contaminant. Gen-
erally, the most important property of the soil in determining the
distribution of contaminants is the soil organic matter, which
normally controls the absorption of hydrophobic compounds.
Table 1 lists some of the relevant physical properties of volatile
and semivolatile organic chemicals that have been, or have the
potential to be, recovered using in-situ thermal techniques.
Many of these are commonly found at Superfund sites and other
sites where ground-water contamination has occurred (Roberts
et al., 1982; Esposito et al., 1989; Newell et al., 1995). All of the
properties listed are temperature dependent. Most of these
organics are essentially immiscible with water; acetone and
methanol are the exceptions. Many of these compounds have
low viscosities and, thus, have the potential to flow readily in the
liquid phase. Approximately half of these compounds are less
dense than water; the other half are more dense than water. The
density of an organic liquid relative to that of water is important
in determining the vertical mobility of the contaminant. Those
that are less dense than water will tend to float on the ground-
water table, while those that are more dense than water may
move downward through the aquifer if the pressure in the organic
liquid is greater than the displacement pressure of the aquifer
materials. Low permeability clay layers in the aquifer may
restrict the vertical movement and allow the liquids to accumu-
late on top of the layer.
Table 1 is set up to list the chemicals in the order of lowest to
highest boiling points. Observation of the vapor pressures
shows that, in general, the lower the boiling point the higher the
vapor pressure at 25°C. The contaminants with the lowest
boiling points also generally have a lower heat of vaporization,
thus these contaminants are relatively easy to volatilize. Com-
pounds with higher boiling points have lower vapor pressures at
ambient temperatures and a higher heat of vaporization, thus
more energy is required to convert them to the gaseous phase.
Laboratory experiments have shown that vaporization of even
highly volatile compounds can cause a measurable decrease in
the temperature of the system (Lingineni and Dhir, 1992).
Henry’s law constants indicate whether the compound prefers to
be in the gaseous or aqueous state. Henry’s law applies to dilute
solutions, and can be written as: P
A
= X
A
H
c
, where P
A
is the partial
pressure of chemical A, X
A
is the mole fraction of chemical A in
solution, and H
c
is a constant, commonly called the Henry’s law
constant. Thus, the Henry’s law constants are a function of the
aqueous solubility and vapor pressure of a compound, and the
greater the Henry’s law constant, the greater the extent to which
the compound partitions to the air phase (Atkins, 1986). The
constants given in the table are expressed in the dimensionless
form, which is a ratio of the concentrations, C
air
/C
water
, where both
concentrations are in mol/m
3
. Due to difficulties involved in
determining solubilities and vapor pressures, reported values of
Henry’s law constants sometimes vary by two orders of magni-
tude or more depending on the source of the data. Mackay and
Shiu (1981) performed a critical review of the available data, and
determined recommended values for many chemicals of envi-
ronmental interest, and a standard deviation of the reported
3
Table 1. Properties of some organic chemicals that have been found at contaminated sites.
Organic Boiling Density Viscosity Water Vapor Vapor Henry’s Law Octanol- Diffusion Diffusion Heat of
Contaminant Point gm/cm
3
cP Solubility Pressure Pressure Constant Water Coefficient Coefficient Vaporiz-
°C 25°C mg/l mm Hg mm Hg dimensionless Partition in Water in Air ation
b
T
1
, °C T
2
, °C 25°C Coefficient cm
2
/day cm
2
/day kJ/mol
25°C
Methylene 40 1.3182 0.413 20,000 260.9 >760 0.105 ± 0.008
n
17.78
q
28.82
Chloride 25°C 20°C
e
10°C 50°C
(Dichloro-
methane)
1,2-Dichloro- 49 1.2444 0.317 600 198.7 >760
ethylene (trans) 20°C
e
10°C 50°C
Acetone 56.3 0.7899 0.306 121.7 622.4 0.000842
k
1.74
e
1.106
b,p,h
9417.6
s
30.99
10°C 50°C 25°C 0°C
1,1-Dichloro- 57.4 1.17 0.464 5500 125.8 608.6 0.234 ± 0.008
n
30
d
30.62
ethane 20°C
e
10°C 50°C 61.7
i
1,2-Dichloro- 60 1.2649 0.445 800 104.8 580.0
ethylene (cis) 25°C 20°C
e
10°C 50°C
Trichloro- 61.2 1.49 0.537 8000 98.6 541.3 0.153 ± 0.012
n
90
d
7862
s
31.28
methane 20°C
e
10°C 50°C 79.4
i
0°C
(Chloroform) 93.3
b
91.2
q
1-Hexene 63.5 0.675 0.252 50 90.0 485.3 16.87 ± 0.40
n
2455
r,h
6212
h
30.61
20°C
e
10°C 50°C 20°C
Methanol 64.6 0.791 0.544 58.5 400 0.151 - 1.11
o
15°C 14,688
g
37.43
10°C 50°C 0.219 1.6
s
25°C
1.43
h
25°C
n-Hexane 68.7 0.659 0.300 9.5 80.8 407.5 68.6 ± 10.1
n
10,000
b
6143
h
31.56
20°C
e
10°C 50°C 12,883
r
20°C
1,1,1-Tri- 74.1 1.3303 0.793 4400 67.4 360.1 1.13 ± 0.016
n
309
b
32.50
chloroethane 25°C 20°C 10°C 50°C 300
d
147.9
i
Continued on next page.
4
Organic Boiling Density Viscosity Water Vapor Vapor Henry’s Law Octanol- Diffusion Diffusion Heat of
Contaminant Point gm/cm
3
cP Solubility Pressure Pressure Constant Water Coefficient Coefficient Vaporiz-
°C 25°C mg/l mm Hg mm Hg dimensionless Partition in Water in Air ation
b
T
1
, °C T
2
, °C 25°C Coefficient cm
2
/day cm
2
/day kJ/mol
25°C
Carbon 76.8 1.5833 0.908 800 58.3 332.8 0.807 ± 0.161
n
676.1
b,q
32.43
Tetrachloride 25°C 20°C
e
10°C 50°C 436.5
e,i
2-Butanone 79.6 0.7994 0.405 26,800 52.6 314.3 0.0010
j
1.820
e
34.76
(Methyl Ethyl 25°C 10°C 50°C 0.00112
c,k
Ketone)
Benzene 80.1 0.88 0.604 1770 47.8 307.8 0.22 ± 0.01
n
134.90
b,e,h,i,l
0.881
b,h
7460
f
33.83
25°C 10°C 50°C 20°C 7819.2
h
0.501
h
2°C 20°C
6653
s
0°C
Cyclohexane 80.7 0.7731 0.894 58 50.5 272.3 7.27 ± 0.81
n
2754
h
0.726
b,h
7430.4
s
33.01
25°C 25°C 10°C 50°C 20°C 45°C
0.397
h
2°C 6212
h
20°C
1,2-Dichloro- 84 1.257 0.779 8700 40.0 278.6 0.044 ± 0.004
n
30.2
b,i
35.61
ethane 20°C 10°C 50°C
Trichloro- 87.3 1.4578 0.545 1100 37.6 256.7 0.397
f
195
b
0.830
f
7030
f
34.54
ethylene 25°C 25°C
e
10°C 50°C 0.38
i
200
d
0.372
a
339
r
Toluene 110.6 0.8647 0.56 515 - 540 14.3 579.1 0.27 ± 0.014
n
537
b
0.734
b,h
6570
f
38.01
25°C 25°C 10°C 100°C 490
d,e,h,i,l
20°C 7119.4
h
447
r
0.389
h
2°C 20°C
6566
s
0°C
7603
s
30°C
7430
o
26°C
7949
o
59°C
Continued on next page.
Table 1 -- Continued.
5
Organic Boiling Density Viscosity Water Vapor Vapor Henry’s Law Octanol- Diffusion Diffusion Heat of
Contaminant Point gm/cm
3
cP Solubility Pressure Pressure Constant Water Coefficient Coefficient Vaporiz-
°C 25°C mg/l mm Hg mm Hg dimensionless Partition in Water in Air ation
b
T
1
, °C T
2
, °C 25°C Coefficient cm
2
/day cm
2
/day kJ/mol
25°C
4-Methyl 116.6 0.802 0.545 19000 4.3 381.0 0.0063
c
40.61
2-Pentanone 10°C 100°C
Tetrachloro- 121.3 1.613 0.844 150 9.0 400 0.928 ± 0.161
n
400
d,e
39.68
ethylene 25°C 25°C 10°C 100°C 407
q
n-Octane 126 0.6986 0.508 0.7 6.5 368.7 121 ± 20
n
104,700
l
4910
f
41.49
25°C 20°C
e
10°C 100°C 151,356
h,r
5166.7
h
20°C
4363
s
0°C
Chloro- 131.7 1.1007 0.753 490 6.9 323.7 0.14 ± 0.02
n
691.8
b,e,i
6394
o
40.97
benzene 25°C 25°C 10°C 100°C 955
r
26°C
7776
o
59°C
6480
s
30°C
Ethylbenzene 136.2 0.8654 0.631 160 6.0 295.7 0.323 ± 0.028
n
1412.5
b,h,i
0.700
b,h
6333
h
42.24
25°C 25°C 10°C 100°C 1349
r
20°C 20°C
0.380
h
2°C
Xylenes 138.4 - 0.8577 0.608 - 160 - 4.5 - 5.6 238.9 - 0.20
f
1412 - 5980
f
42.40 -
144.4 - 0.802 180 10°C 280.8 9400
j
1585
b
5771.5
h
43.43
0.8764 25°C 100°C 0.202 - 0.286
c
588.8 - 20°C
25°C 0.214
a
1584.9
e,h,l
1349 -
1585
r
n-Decane 174.2 0.730 0.838 0.052 3.0 77.7 282.5 ± 121
n
51.38
25°C 100°C
Dichloro- 173 - 1.2988 1.044 - 80 - 150 2.2 67.1 0.048 - 0.073
b
2399 - 36.18 -
Benzene 180 25°C 1.324 25°C 25°C 100°C 3981
b
49.00
(3 isomers) (ortho 2399 -
isomer) 2455
e
Dodecane 216.5 0.75 1.383 0.0034 19.5 302.7 ± 100.9
n
1537
l
61.51
100°C 13 x 10
6
h
Continued on next page.
Table 1 -- Continued.
6
Organic Boiling Density Viscosity Water Vapor Vapor Henry’s Law Octanol- Diffusion Diffusion Heat of
Contaminant Point gm/cm
3
cP Solubility Pressure Pressure Constant Water Coefficient Coefficient Vaporiz-
°C 25°C mg/l mm Hg mm Hg dimensionless Partition in Water in Air ation
b
T
1
, °C T
2
, °C 25°C Coefficient cm
2
/day cm
2
/day kJ/mol
25°C
Naphthalene 218 0.97 32 22.7 0.02
b,i
2239
b,r
4432
s
0°C
25°C 100°C 0.05
m
2344.2
i
0.017 ± 0.002
n
1738
l
1-Methyl 244.8 1.020 28.5 0.043 0.0182 ± 7413
r
naphthalene kg/m3 0.0016
n
Hexadecane 286.9 0.773 3.032 0.0063 < 1 < 1 81.38
Phenanthrene 340 0.98 1.18 0.0016
i,m
28,840
e,i
72.50
0.0016 ± 37154
r
0.00032
n
Gasoline 0.73 0.45 100 - 300 6272.6
h
0.7182
h
0.4 - 0.6
h
30 - 120
h
20°C
20°C 20°C
Superscripts
a - Baehr, 1987 b - Lide, 1993 c - Newell et al., 1995 d - Hunt et al., 1988 e - Verschueren, 1983 f - Ong et al., 1992
g - Thoma et al., 1992 h - Lyman et al., 1991 i - Ryan et al., 1988 j - Jury et al., 1990 k - Sanders, 1995 l - Johnson et al., 1990
m - Jury et al., 1984 n - Mackay and Shiu, 1981 o - Treybal, 1980 p - Tyn and Calus, 1975 q - Valsaraj, 1988
r - Miller et al., 1985 s - Perry and Chilton, 1973
Table 1 -- Continued.
7
values that were thought to be reliable. For chemicals for which
their recommended values are available, they are listed in
Table 1. For the other chemicals, all reported values that were
located in the literature are listed to show the range in reported
values. The Henry’s law constants listed in the table show that
at ambient temperatures, the alkanes and similar compounds,
such as 1-hexene and cyclohexane, have a strong preference
for the air phase rather than the aqueous phase, while the
chlorinated solvents and compounds that contain a benzene
ring tend to concentrate more in the aqueous phase. As the
number of benzene rings in the compound increases, its prefer-
ence for the aqueous phase increases. The ketones listed in
Table 1 also have a very strong preference for the water phase.
The partition coefficient is defined as the ratio of the equilibrium
concentration C of a dissolved substance in a system containing
two largely immiscible solvents. Thus, the octanol-water parti-
tion coefficient is defined as K
ow
= C
octanol
/C
water
. The octanol-
water partition coefficient has proven useful as a means to
predict soil absorption as well as biological uptake and
biomagnification and related phenomenon (Verschueren, 1983).
In general, the more hydrophobic a compound is, the greater its
octanol-water partition coefficient and the greater its absorption
onto soil organic matter (Karickhoff et al., 1979). However, this
generalization is limited to hydrophobic organic compounds and
soils which contain significant amounts of organic matter, on the
order of at least 0.1 percent (Schwarzenbach and Westall, 1981;
Weber et al., 1991). Most of the organic compounds listed in
Table 1 are at least moderately hydrophobic, thus the octanol/
water partition coefficient might be expected to indicate the
degree of absorption of these compounds in surface soils or
other soils with high organic carbon contents. It can be seen in
Table 1 that there are also some large differences in the reported
values for the octanol/water partition coefficients for a given
organic compound depending on the source of the data. Despite
these differences, the reported values show that most of the
compounds listed have a strong preference for organic matter
rather than the water phase, with the exception being the
ketones and methanol. The absorption of contaminants into the
soil organic matter will tend to limit the rate at which they can be
recovered in either the aqueous or gaseous phase.
To illustrate what the Henry’s law constants and octanol-water
partition coefficients indicate about the distribution of an organic
chemical in the subsurface, a few calculations were carried out
using the equations given by Feenstra et al. (1991). The results
of these calculations are shown in Table 2. A surface soil of loam
texture with a bulk density of 1.28 gm/cm
3
, a porosity of 0.30, a
water saturation of 50 percent, and an organic matter content of
2 percent was assumed. Karickhoff et al.’s (1979) relationship
between the octanol-water partition coefficient and the adsorp-
tion coefficient, K
d
, was assumed to be valid: K
d
0.6f
oc
K
ow
, where
f
oc
is the fraction of organic matter in the soil. In order to
demonstrate the effect of soil properties on the distribution of an
organic chemical, calculations were also done for the same
chemicals for a sandy soil of bulk density 1.86 gm/cm
3
, porosity
0.30, and organic matter 0.1 percent. Again, a 50 percent water
saturation was assumed.
Table 2 shows that in soils with high organic carbon content,
organic compounds may be highly associated with the solid
material. Calculations for 1,1,1-trichloroethane (TCA) were
carried out using the range of values that have been reported for
K
ow
for this chemical to illustrate the difference this can make in
the calculated distributions. For soils with high organic matter
content there is very little difference as most of the chemical is
still associated with the solids. For low organic matter conditions
the difference in the distribution is significant, and the lower K
ow
value means that more of the chemical is recoverable in the
water or air phase. Trichloroethylene (TCE) and TCA have
similar K
ow
values at ambient temperatures, but TCA has a
Henry’s law constant that is greater than that of TCE at tempera-
tures around 20°C and, thus, much more of the TCA will be in the
air phase. TCE is a volatile organic compound but, at 20°C,
significantly more of its mass will be in the aqueous phase rather
than in the gas phase; a very significant proportion of it will be
associated with the solids. Acetone is highly volatile with a
boiling point of 56°C, but its extremely low K
ow
and H
c
concentrate
it in the aqueous phase. Because acetone is miscible with water
and is a good solvent for many organic chemicals, acetone may
significantly increase the transport of less soluble organic chemi-
cals in ground water (Huling, 1989; Udell and Stewart, 1989).
The diffusion coefficient measures the rate at which molecules
spread down a concentration gradient, and is dependent on the
chemical nature of the system and the concentration, as well as
the temperature and pressure. As can be seen from the
coefficients listed in Table 1, diffusion in gases is much greater
than diffusion in liquids, which is due to the considerably higher
molecular concentration of liquids. When experimental data is
not available, the diffusion coefficient for gases can be estimated
fairly accurately by equations that have been developed based
on the kinetic theory of gases. For liquids, diffusion coefficients
cannot be estimated with the same degree of accuracy because
a sound theory of the structure of liquids has not been devel-
oped. However, empirical correlations have been developed
and can be used in the absence of laboratory data (Treybal,
1980). Observation of the values in the table shows that most of
the organic compounds for which values could be located fall in
the range of 5000 to 8000 cm
2
/day for diffusion in air; methanol
and acetone are again the exceptions with larger coefficients. All
of the water diffusion coefficients, also, fall in a rather narrow
range from 0.7 to 1.6 cm
2
/day.
The properties listed in Table 1 are for pure chemicals, and do
not consider the effects of a porous solid on the properties and
behavior of the chemical. The vapor pressure, the diffusion
coefficient in both air and water, and perhaps the viscosity, are
all significantly affected by the presence of the chemical in
porous media and the properties of that media. The partial
pressure of a liquid is dependent on the curvature of the interface
between the liquid and gaseous phases, and the values con-
tained in Table 1 are for a flat interface. When the interface is
curved, the partial pressure of the liquid is reduced. Although
this effect is very small in sandy soils with a less than one percent
reduction in vapor pressure, it becomes important in clay soils
when the pore sizes are less than approximately 10
-6
cm,
8
Table 2. Distribution of chemicals in low and high organic matter content soils.
High Organic Matter Low Organic Matter
Air Water Solids Air Water Solids
1,1,1-Trichloroethane 5% 5% 90% 26% 23% 51%
P
oct
= 300
1,1,1-Trichloroethane 6% 6% 88% 35% 31% 34%
P
oct
= 147.9
Trichloroethylene 1.6% 4.6% 93.8% 14% 35% 52%
20°C
Trichloroethylene 30% 7% 63% 73% 16% 11%
90°C
Acetone 0.07% 85% 15% 0.08% 99% 1%
causing a decrease in vapor pressure of approximately 40 per-
cent (Wilson et al., 1988). This effect can also be important when
the medium is dry and the remaining liquid has receded into the
smallest pores (Bear and Gilman, 1995). These capillarity
effects will determine the level of cleanup that can be achieved
by a venting process at a given temperature (Lingineni and Dhir,
1992).
Adsorption of the organic onto the solid phase or partitioning into
the soil organic matter can also have the effect of lowering the
partial pressure of an organic compound. Adsorption can occur
from the liquid onto the solid and, when the water content is very
low, from the vapor phase onto the soil surface (Lighty et al,
1990; Tognotti et al., 1991). Fares et al. (1995) have studied
desorption of TCE from soils, and their data shows that the
equilibrium vapor pressure of TCE as it desorbs from a soil is
approximately an order of magnitude lower than the partial vapor
pressure of TCE when no soil is present. Experiments per-
formed by Arthurs et al. (1995) showed that the rate of volatiliza-
tion of the liquid in the presence of a soil is about two orders of
magnitude slower than from the pure liquid, and that the vapor-
ization rate increases as the vapor pressure of the compound
increases. Fares et al. (1995) and Keyes and Silcox (1994)
found that the rate of desorption was linearly correlated with the
inverse of the soil particle diameter. Hatzinger and Alexander
(1995) found that organic compounds may become more tightly
bound to the soil or organic matter with time, which reduces their
desorption. Thus, the equilibrium partial pressure of a volatile
contaminant in the pore space and mass transfer from the
aqueous liquid or adsorbed phase will depend on the properties
of the chemical and the soil environment in which it resides.
The diffusion coefficients listed in the table are for bulk air or
water. In the pore spaces of a soil, diffusion in both the air and
water phase is reduced because of the reduced cross-sectional
area and increased path length caused by the presence of solid
and liquid obstacles (Millington, 1959). Diffusion coefficients in
porous media are a function of both the porosity of the soil and
the water (or air) content of the pores. At low water contents,
diffusivity in the water is also limited by the continuity of the water
phase. For diffusion in water in porous media, Porter et al. (1960)
found a nearly linear increase in effective diffusion as the water
content increased, ranging from 4 to 30 percent of its diffusion in
bulk water. Jin and Jury (1996) recommended the use of a
second model developed by Millington (1959) for predicting gas
phase diffusion in disturbed porous media: D
s
/D
a
= a
2
/n
2/3
, where
D
s
is the diffusion coefficient of a gas through soil, D
a
is the
diffusion coefficient in free air, a is the volumetric air content of
the pores, and n is the porosity. They did not find a unique
relationship for gaseous diffusion in undisturbed soils due to
their heterogeneous nature. Measured gas phase diffusion in
undisturbed soils is both higher and lower than predicted by this
theory, but is not generally greater than about 40 percent of the
diffusion in air, and the diffusion drops off rapidly as the air-filled
porosity decreases.
Adsorption of water onto solid surfaces, particularly onto the
reactive surfaces of clays, will increase the viscosity of the water
in the layers immediately adjacent to the clay surface. Theoreti-
cal and experimental results of Kemper (1961a, 1961b) indi-
cated that the first layer of water on the surface of a clay may
have a viscosity on the order of 10 times that of the bulk water,
and the viscosity of each adjacent layer of water then decreases
9
rapidly to the viscosity of the bulk water. How much effect this
has on bulk flow in soils depends on the thickness of the water
films in proportion to the pore sizes. Neutral organic species will
generally not be adsorbed to the surface of the soil as strongly
as water. Therefore, neutral organics may have a smaller
effective viscosity relative to that of water in porous media,
allowing them to flow more readily. For clays that are highly
reactive and swell in the presence of water, research has shown
that the presence of organic chemicals may shrink the clay.
Cracks may form which allow a much greater flow of the organic
chemical than was possible with water (Anderson et al., 1985;
Brown and Thomas, 1987; Fernandez and Quigley, 1988).
Table 3 lists a few of the viscous oils that have been found
contaminating the subsurface. These oils are essentially non-
volatile and are not soluble to an appreciable degree in water.
Thus, they remain a separate liquid phase in the subsurface. All
of these oils are mixtures of many different hydrocarbons. Coal
tar and creosote also contain polycyclic aromatic hydrocarbons.
When oils such as these are spilled to the subsurface and are
exposed to air and water, "weathering" will occur, as the more
volatile hydrocarbons volatilize to the pore air, and the more
soluble hydrocarbons dissolve in the pore water. Water and air
moving past these oils while they are trapped in the subsurface
will enhance the weathering process. The loss of the “light”
hydrocarbons by the weathering process will increase the spe-
cific gravity and viscosity of the remaining oil, and lower the
surface and interfacial tensions. Measurements made in the
author’s laboratory, Robert S. Kerr Environmental Research
Center, showed that a significant proportion of the crude oil was
volatilized at room temperature, causing a 7-fold increase in
viscosity. Creosote was found to contain few volatiles at room
temperature, and weathering did not change its viscosity signifi-
cantly. The specific gravity of both oils increased, and the
surface and interfacial tensions decreased by approximately 5 to
10 dynes/cm by the weathering. Mungan (1964, 1966) has
found that decreasing the interfacial tension in an immiscible
displacement will increase recovery of the oil. Although de-
creases in interfacial tension will favor recovery of these oils, that
may be offset by a decrease in mobility caused by the higher
viscosities.
Research in the author’s laboratory has shown that oils such as
the crude oil listed in Table 3 flows more readily through some
silica sands than would be predicted based on the intrinsic
permeability of the sand measured with water and the density
and viscosity of the crude oil. This is likely due to the nonpolar
nature of these hydrocarbons which limits their adsorption to soil
surfaces. The greater mobility of the crude oil would give it a
greater tendency to spread as it enters the subsurface, but also
should aid in its recovery by a displacement process such as hot
water injection.
Mechanisms for Enhanced Recovery
In general, when an organic chemical is heated, its density is
reduced, its vapor pressure is increased, its adsorption onto
solid phases or absorption into soil organic matter is decreased,
and its molecular diffusion in the aqueous and gaseous phase is
increased (Isherwood et al., 1992). The viscosity of a liquid will
decrease as the temperature is increased, but the viscosity of
gases increases with temperature. Which of these effects of
heat is important for the enhanced recovery of a particular
contaminant depends mostly on the properties of the contami-
nant and the mechanism limiting the removal rate of the contami-
nant in the particular circumstance.
Available data on the expansion of organic chemicals such as
those listed in Table 1 with temperature shows that these
chemicals expand approximately 0.1 percent per degree Cel-
sius. Thus, increasing the temperature by 100°C will increase
the liquid volume by approximately 10 percent. Since the volume
of a gas is directly proportional to temperature given in Kelvin, a
100°C increase in temperature will cause approximately a 30 per-
cent increase in the gas volume. These changes are small
compared to the volume change that occurs when a liquid is
converted to a gas; water at 100°C has approximately a 1600-fold
increase in volume when it is converted from a liquid to a vapor.
The expansion of liquids with temperature causes a reduction in
the interaction between molecules, and thus a reduction in its
viscosity. For the organic chemicals listed in Table 1, generally
there is about a one percent change in viscosity per degree
Celsius. Thus, the higher the viscosity of the liquid at ambient
temperatures, the greater the reduction in viscosity as the
temperature is increased. The viscosity of gases at ambient
temperatures is approximately one to two orders of magnitude
lower than the viscosity of liquids. However, the increase in the
velocity of gas molecules with temperature is such that it causes
greater interaction between molecules as the temperature in-
creases, causing an increase in viscosity with temperature. This
increase is proportional to the temperature in degrees Kelvin, so
that a 100°C increase in temperature will increase the viscosity
of a gas by about 30 percent.
The effect of temperature on solubility is dependent on the
chemical. Increasing temperature will reduce the water-water,
water-solute, and solute-solute interactions, so the net effect of
temperature on solubility will depend on which interactions are
affected to the greatest extent (Yalkowsky and Banerjee, 1992).
Thus, some chemicals show increasing solubility with tempera-
ture while others show decreasing solubility with temperature.
Maximum or minimum solubilities with temperature have also
been found for some chemicals; many organic liquids exhibit
minima in solubility at about room temperature (Yalkowsky and
Banerjee, 1992). Measurements by Stephenson (1992) and the
data compiled by Horvath (1982) show that the solubility of the
organic chemicals listed in Table 1 often decreases in the
temperature range of 0°C to 90°C, but the change in solubility in
this temperature range is generally less than a factor of two.
Vapor pressures always increase with temperature. For the
organics listed that have a boiling point of less than 100°C, the
vapor pressure increases by a factor of 5 to 7 as the temperature
increases from 10°C to 50°C. For those compounds that have
a boiling point greater than 100°C, their vapor pressure generally
increases by a factor of 40 to 50 by raising the temperature from
10°C to 100°C. Limited data on the desorption of organics from
10
soils shows that the exponential increase in the vapor pressure
with temperature also holds when the organic chemical is in the
presence of soils (Fares et al., 1995).
The combination of only small changes in solubility with tem-
perature but large increases in vapor pressure results in in-
creases in Henry’s constant as a function of temperature.
However, very few measurements of Henry’s constants for
chemicals of environmental concern as a function of tempera-
ture have been made, and most of these measurements are over
a limited temperature range. Heron et al. (1996) calculated and
measured H
c
values for TCE as a function of temperature and
found an order of magnitude increase when the temperature was
raised from 20°C to 90°C. For the more soluble compounds such
as dichloromethane or 2-butanone, and the water-miscible com-
pounds such as acetone and methanol, H
c
may not be influenced
significantly by temperature.
Few measurements of K
ow
and/or K
d
have been made as a
function of temperature, and most of the measurements that
have been made are over very small temperature ranges.
Although it has been shown for some systems that adsorption
may increase with temperature over narrow temperature ranges
(Weber et al., 1983), adsorption is, in general, an exothermic
process and, thus, will decrease as the temperature increases.
The magnitude of the effect of temperature is dependent on the
particular chemical, the soil, and the water content, as these
factors will determine the mechanism causing the adsorption
(Cancela et al., 1992; Piatt et al., 1996). Heron et al. (1996)
showed theoretically, based on heats of sorption, that adsorp-
tion from the aqueous phase onto soils can be expected to
decrease by a factor of approximately 2.2 as the temperature is
increased from 20°C to 90°C. Adsorption from the vapor phase
onto dry soils generally has a larger heat of sorption, which leads
to a greater influence of temperature on the adsorption process.
For TCE, Heron et al. (1996) found approximately an order of
magnitude decrease in adsorption onto dry soil as the tempera-
ture was increased from 20°C to 90°C. For high molecular
weight organics such as PCBs, a large fraction of the organic
may remain adsorbed to the soil at ambient temperatures, and
significantly higher temperatures (300°C to 400°C) may be
required for desorption to occur (Uzgiris et al., 1995).
Measured data has shown that the diffusion coefficient in liquids
is proportional to temperature in degrees Kelvin. Increasing the
temperature from 10°C to 100°C will increase the diffusion of a
Table 3. Properties of some oily contaminants.
Boiling Specific Viscosity Water Vapor Surface Interfacial
Range Gravity cp Solubility Pressure Tension Tension
mg/l mm Hg dynes/cm dynes/cm
Automatic > 350°C 0.875 < 50 < 2 x 10
-4
33.7
Transmission 20°C 20°C
Fluid
a
Coal Tar
b
25°C 0.9744 25°C 41.4
60°C 0.9469 60°C 1.65
85°C 0.9263 85°C 1.16
Coal Tar
c
50% can be 7°C 1.028 7°C 18.98 28.8 22
distilled at 15°C 1.017 50°C 5.04 22°C
270°C 38°C 0.991 60°C 3.89
60°C 0.985
Creosote
d
45 to 65% 10°C 1.1060 10°C 35.7 10°C 32.4 9.65 10°C
can be 20°C 1.1027 20°C 19.8 20°C 33.5 7.83 20°C
distilled at 30°C 1.0957 30°C 12.4 30°C 29.0 6.16 30°C
315°C
e
40°C 1.0893 40°C 8.57 40°C 25.0 5.31 40°C
50°C 1.0816 50°C 6.17 50°C 26.8 5.90 50°C
Crude Oil
d
10°C 0.8953 10°C 160.2 10°C 26.2 22.0 10°C
20°C 0.8883 20°C 63.0 20°C 24.5 21.0 20°C
30°C 0.8820 30°C 34.8 30°C 23.2 20.5 30°C
40°C 0.8760 40°C 23.2 40°C 23.3 20.2 40°C
50°C 0.8680 50°C 16.4 50°C 22.8 21.4 50°C
a - Abdul et al., 1990 b - Johnson and Guffey, 1990 c - Villaume et al., 1983 d - unpublished data from the author’s lab
e - American Wood Preservers’ Association Standards
11
solute in the aqueous phase by approximately 30 percent
(Treybal, 1980). The diffusion coefficient for gases is also
dependent on temperature. Observation of the theoretical
equation for diffusivity in the gas phase developed for mixtures
of nonpolar gases or of a polar with a nonpolar gas shows that
the diffusivity varies almost as T
3/2
(Treybal, 1980). Increasing
the temperature from 10°C to 100°C will increase diffusion in the
air phase by approximately 50 percent, while a temperature
increase from 10°C to 300°C will increase diffusion by approxi-
mately 200 percent.
Essentially all of these changes with temperature can aid in the
recovery of contaminants from the subsurface. The thermal
expansion of a liquid with its accompanying decrease in viscos-
ity will allow the heated liquid to flow more readily. For gases, the
expansion with temperature will be largely offset by the increase
in viscosity. However, since the viscosity of gases is approxi-
mately two orders of magnitude lower than the viscosity of
liquids, conversion of a liquid to a gas will greatly increase its
mobility. The act of expansion itself will aid in moving the fluids
out of the pore space, with the greatest effects coming from the
vaporization of a liquid to a gas. The increased diffusion of
contaminants as the temperature increases in both the aqueous
and gaseous phases will help to move contaminants from areas
of low permeability to areas of high permeability and speed their
recovery.
To demonstrate the effects of temperature on the distribution of
organic contaminants between the phases in the subsurface,
calculations were carried out using the data of Heron et al. (1996)
for TCE at 90°C. The results are shown in Table 2. It can be seen
that raising the temperature to 90°C significantly increases the
concentration in the air phase under both the high and low soil
organic matter conditions, while significantly decreasing the
amount that is associated with the solids. Only small amounts
remain in the liquid phase. Thus, as the temperature is in-
creased, significantly more of the TCE can be recovered in the
vapor phase. If the high organic matter content soil is considered
under water saturated conditions, the amount of TCE in the
water would approximately double as the temperature was
increased from 20°C to 90°C, but 82 percent of the TCE would
remain adsorbed to the solids. Under the low organic matter/water
saturated conditions, there would be approximately a 30 percent
increase in the amount of TCE in the water phase when the
temperature is increased from 20°C to 90°C, leaving approxi-
mately 25 percent adsorbed to the solids.
This small effect of temperature on the concentration in the
aqueous phase shows that raising the temperature would have
a limited effect on the recovery in a pump-and-treat system. For
the volatile and semivolatile organic compounds, such as those
listed in Table 1, the enhanced vapor pressure and rate of
vaporization are generally the most important mechanisms for
enhanced recovery using the in-situ heat based remediation
techniques. Some of the most volatile compounds, which
includes TCE, benzene, and toluene, can be removed fairly
efficiently from sandy soils by vacuum extraction alone (Ho and
Udell, 1992; Gauglitz et al., 1994; Shah et al., 1995), and
laboratory experiments on vacuum extraction have shown that
the addition of heat had little effect on the vaporization of the less
volatile compounds. For the higher boiling point compounds and
when clays are present in the subsurface, the addition of heat as
part of the remediation process will significantly increase volatil-
ization and enhance the vacuum extraction process (Lingineni
and Dhir, 1992). Recovery of most of these chemicals from the
subsurface will be enhanced by either steam or hot air injection
or by electrical heating processes.
For the volatile and semivolatile contaminants, steam stripping
and steam distillation can also be important recovery mecha-
nisms (Dev et al., 1989; Stewart and Udell, 1988). Steam
distillation occurs when an immiscible liquid is present along with
water, as the mixture of immiscible liquids will boil when the total
pressure reaches one atmosphere, rather than when the pres-
sure of the individual component reaches one atmosphere.
Because both liquids are contributing to the vapor pressure, the
vapor pressure reaches one atmosphere at a lower temperature
than either of the individual components would (Atkins, 1986).
Steam stripping enhances volatilization of a volatile organic
compound by removing the vapor phase from contact with the
aqueous phase, thus preventing the liquid and vapor phases
from reaching equilibrium and allowing volatilization to continue.
Steam stripping becomes important when an immiscible phase
is not present (Dev et al., 1989).
For the types of contaminants listed in Table 3, the greatest
enhancement effect coming from the addition of heat is likely to
be a reduction in the viscosity of the oil phase. Highly viscous oils
will generally show a substantial decrease in viscosity with only
a moderate temperature increase above ambient temperatures
(Herbeck et al., 1976), and the rate of decrease with temperature
then drops off rapidly with continuing increases in temperature.
Edmondson (1965) found that the greater the dependence of
viscosity of the oil on temperature, the greater the increase in its
recovery by a hot water displacement as the temperature in-
creased. Other mechanisms for the increased recovery of oils
by hot water include the thermal swelling of liquids (Willman et
al., 1961), shifts in the relative permeabilities to oil and water with
temperature, and decreases in the residual oil saturation
(Edmondson, 1965; Davidson, 1969; Poston et al., 1970; Davis
and Lien, 1993). Decreases in the interfacial tension with
temperature for contaminants such as creosote may also aid in
its recovery from the subsurface. Different researchers have
found shifts of varying magnitudes and directions in relative
permeability curves, but in all cases the increase in oil recovery
as the temperature increases always appears to be greater than
would be predicted based on the viscosity reduction alone.
Capillary pressure-saturation curves measured for two phase
water/oil systems have shown substantial decreases in the
residual oil phase as the temperature increased (Davis, 1994),
and thus, a greater portion of the oil may be recoverable as the
temperature is increased.
Heat-based In-situ Remediation Techniques
There are three general methods that can be used to inject or
apply heat to the subsurface to enhance remediation: injection
in the form of hot gases such as steam or air, electromagnetic
12
energy heating, and hot water injection. Another thermal
remediation technique that relies on thermal conduction of soil to
heat the subsurface is also under development (Iben et al.,
1996), but will not be discussed here. All of these methods were
first developed by the petroleum industry for enhanced oil
recovery, and have more recently been adapted to soil and
aquifer remediation applications. The two applications have
significantly different objectives. In oil recovery operations, the
reservoir initially has a large oil saturation, and the objective is
to recover as much as possible economically. In these opera-
tions, a large residual oil saturation of as much as 50 percent or
more may be acceptable. In contamination remediation applica-
tions, the initial saturation of the contaminant may be anywhere
from essentially fully saturated to less than residual saturation,
and the objective is to reduce the contaminant concentration to
very low levels. The techniques of steam injection, electrical
energy application, and hot water injection have been the
subject of extensive research and development, and it has been
established that these techniques are effective for the remediation
of organic contaminants when they are appropriately applied
(Fulton et al., 1991; Davis and Lien, 1993; U.S. EPA, 1995a;
Newmark and Aines, 1995).
Injection of hot air has been tried in the laboratory and found to
enhance the removal of contaminants from one-dimensional soil
columns (Lingineni and Dhir, 1992; Shah et al., 1995). However,
the use of hot air in the field is limited by the very low heat
capacity of air (approximately 1 kJ/kg °C) (Ramey, 1967).
Steam, with a heat capacity that is approximately four times that
of air (approximately 4 kJ/kg °C), and heat of evaporation of more
than 2000 kJ/kg, has been used successfully to heat soils,
aquifers and reservoirs to enhance the recovery of contaminants
and oils. However, the injection of steam will always leave
behind a residual water saturation (Stewart and Udell, 1988),
and contaminants that have a significant solubility in water may
remain at high concentrations in this residual water or may even
appear to increase in concentration (Udell and Stewart, 1989;
U.S. EPA, 1991). For these situations, recovery of the contami-
nants may require that the soil be dried, and hot air injection may
be applicable (Farrington, 1996).
Steam, hot air and hot water injection rely on contact between the
injected fluid and the contaminant for the transfer of heat to and
recovery of the contaminant. Steam injection will displace
mobile contaminants in front of the steam as well as vaporize
volatile residual contaminants, and therefore can recover vola-
tile contaminants in both the liquid or vapor phase. Hot air
injection has been used to recover contaminants only in the
vapor phase. Hot water injection generally recovers contami-
nants only in the liquid phase. Thus, steam injection is appli-
cable to volatile and semivolatile organic compounds that are
immiscible with water, hot air is applicable to volatile and
semivolatile organics that are water soluble, and hot water
injection is applicable for the oils that have low volatility and very
low solubility in water. The main mechanism for enhanced
recovery using hot water is generally a reduction in the viscosity.
Changes in relative permeability and reductions in residual
saturation are likely to also aid in the recovery of nonvolatile oils.
Hot water injection is most likely effective only when the non-
aqueous phase is present in quantities greater than the residual
saturation, as the main recovery mechanism is the physical
displacement of the nonaqueous phase. Hot water injection may
be most effective for light oils that are floating on top of the water
table, as the lower-density hot water has a tendency to rise if
injected below the water table. For oils that are more dense than
water at ambient temperatures but less dense than water at the
displacement temperature, heating of the subsurface by hot
water injection may help to float these oils, which may aid in their
recovery (Johnson and Guffey, 1990). Steam injection has a
definite advantage over hot water injection when the contami-
nants have a low boiling point and are present as an immiscible
phase, and thus can be steam distilled at the temperatures
achieved by steam injection (Willman et al., 1961). Field trials
have shown that steam injection can be carried out above or
below the water table (Udell and Stewart, 1989; U.S. EPA, 1991;
Aines et al., 1992).
There are limitations on the pressures that can be used for steam
and hot water displacement processes, and this limits the
viscosity of the fluid that can be displaced from a media with a
certain permeability. However, volatilization processes using
steam or hot air may still be possible in low permeability media
(Farrington, 1996), and for highly viscous oil, it may be possible
to heat the oil and lower its viscosity sufficiently to recover at
least a portion of the oil by either a displacement process or
gravity drainage (Hall and Bowman, 1973; Vogel, 1992).
Electrical energy has been applied to the soil in the low fre-
quency range used for electrical power (called electromagnetic
(EM), alternating current (AC), or resistivity heating) as well as
in the radio frequency (RF) range. When EM heating is used, the
water in the pore spaces of the soil absorbs essentially all the
applied energy, so the evaporation of water limits the transport
of energy in the soil and, therefore, limits the heating process.
Thus, for the low frequency methods, the boiling point of water
is the highest temperature that can be achieved. For semivolatile
organic contaminants, the vapor pressure at 100°C may not be
adequate to effectively recover the contaminants. For this
reason, researchers have also developed the use of RF energy
for soil heating. RF energy can be absorbed by the soil itself, and
thus is not limited by a lack of water in the pore space. Using RF
energy, the upper temperature limit of the technique is 300°C to
400°C (Dev, 1993; Sresty, 1994). For electrical heating, the
electrical properties of the soil and the presence of water are
important in determining the efficiency of the heating process
(Dev et al., 1989; Marley et al., 1993). The electrical heating
techniques are recommended for the removal of organic con-
taminants which exhibit a vapor pressure of at least 10 mm Hg
in the treatment temperature range (Sresty, 1994). There is
some evidence that high molecular weight organics, such as
organopesticides, can be broken down to simpler organics such
as acetone, benzene and toluene, at the temperatures and
conditions that can be achieved by RF heating (U.S. EPA,
1995b&c; Swanstrom and Besmer, 1995). Electrical heating
has been proven effective in sandy media (Dev, 1986), and also
has a greater potential than steam or hot water injection to be
effective in less permeable media such as clays. The higher
water content generally found in the clay will aid in directing the
13
electromagnetic energy to the clay and allow a faster heating
rate and higher temperatures to be achieved. RF heating,
however, is limited to the unsaturated zone. For contaminants
trapped below the water table, dewatering would have to be
done prior to electrical heating (U.S. EPA, 1995b).
Because steam injection (at least in its initial stages) and hot
water injection are displacement processes, they can also
recover nonvolatile contaminants dissolved in the aqueous
phase, such as salts (Vaughan et al., 1993), but heat does not
necessarily enhance the recovery of this type of inorganic
contaminant. Metals, with the exception of mercury, cannot be
recovered from soils by thermal means. Mercury has a signifi-
cant vapor pressure at ambient temperatures, and it increases
as the temperature increases. Adsorption onto soils and other
materials can reduce its partial vapor pressure significantly, and
it was found that drying soil samples to 100°C did not recover
measurable amounts of mercury. At temperatures of 200°C and
greater, significant amounts of mercury can be recovered from
soils, reducing the residual remaining in the soil to as little as 1
part per million at 400°C (Dewing and Schluter, 1994).
Each of these thermal methods is generally applicable only to
certain types of contaminated sites, and it is important that the
appropriate heat-based remediation technique is chosen for a
given site. The choice of technique must be based on both the
characteristics of the subsurface and of the contaminants to be
recovered. Steam or hot air injection or the electrical heating
techniques are generally applicable for the types of chemicals
that are listed in Table 1, while hot water injection is generally
applicable for the nonvolatile oils listed in Table 3. The perme-
ability of the media, the amount and type of heterogeneity, the
amount of adsorption, and the solubility of the contaminant must
all be considered when choosing between the technologies.
Electrical heating may be favored in low permeable media and
when there is significant heterogeneity. For highly soluble
contaminants, drying the soil may be necessary and, thus, hot air
or RF heating may be more applicable. Because desorption can
be a slow process, higher temperatures and/or longer remediation
times may be necessary when adsorption is significant.
Figure 1 can be used as a quick guide to determine which of the
techniques would likely be applicable for a given situation; in
some cases, more than one technique may be applicable. The
principle that has been applied in developing this figure is to
recommend the least severe technique, in terms of temperature
and pressure requirements, that is likely to be able to recover the
contaminants. For example, although hot water and steam
injection may both be able to recover a nonvolatile, viscous oil,
hot water injection is recommended because it will generally
recover the same amount of this type of oil (Willman et al., 1961)
at a lower temperature. Equipment and facilities for generating
and handling hot water are relatively simple and inexpensive
(Harmsen, 1971), but the generation and transport of steam
involves more complex and expensive systems. Higher operat-
ing temperatures also mean greater safety risks (Herbeck et al.,
1976). The Issue Paper specific to that technique can then be
consulted for further information.
Comparison to Other In-situ Techniques
The one significant advantage of heat-based remediation tech-
niques over other in-situ remediation techniques is that these
methods do not require that chemicals of any sort be injected into
the subsurface as part of the remediation effort. This is a very
significant advantage over the surfactant and cosolvent tech-
niques because surfactants and cosolvents may themselves
have toxic properties, and it may not be possible to recover all of
the injected chemicals. Also, when surfactants or cosolvents are
used, the technique may be limited by a lack of contact between
the injected chemical and the contaminants, which can be
caused by low permeability layers within the media or by reduc-
tions in relative permeability to one phase because of the
presence in the pores of another phase (Peters et al., 1991).
With the in-situ heating techniques discussed in these Issue
Papers, heating of the entire area to be treated has generally
been accomplished (Aines et al., 1992; Gauglitz et al., 1994).
These heating techniques can be used with a technique such as
vacuum extraction, with benefits that may be significantly greater
than for either process used separately (Udell and Stewart,
1989; Jarosch et al., 1994). Also, these processes are appli-
cable in heavily contaminated soils, the “hot spots” of contami-
nated sites, which generally are very important to clean up in
order to stop the spread of the contamination, and where
biological treatment may not be effective (Johnson and Guffey,
1990; Aines et al., 1992).
These thermal techniques initially may be limited by subsurface
heterogeneities, which affects all other in-situ remediation tech-
niques. When low permeability clay lenses are present in an
aquifer, the injected fluids often bypass these low permeability
areas and, therefore, do not contact the contaminants contained
within them. With time, however, the heat will be conducted into
the lower permeability areas. Also, the Dynamic Underground
Stripping Process, developed by the Lawrence Livermore Na-
tional Laboratory, circumvented this problem for the case where
relatively thick clay layers are interbeded with sandy layers by
combining both steam injection and electromagnetic heating
with vacuum extraction (Newmark and Aines, 1995; Yow et al.,
1995).
Research has shown that complete desorption of chemicals
from clay soils, or soils containing a significant amount of natural
organic material, may require extreme temperature conditions
(Lighty et al., 1988; Tognotti et al., 1991), which may not be
achievable in-situ. Thus, in many cases, a secondary or polish-
ing step may be required to achieve very low contaminant
concentrations (Yow et al., 1995). Hot water injection or shallow
steam injection applications where low temperature and pres-
sures are used may leave the subsurface system amenable to
bioremediation. In fact, raising the temperature above ambient
temperatures may, in many instances, enhance naturally occur-
ring biodegradation of contaminants (Isherwood et al., 1992).
However, if steam is injected into the deeper subsurface at high
temperatures and pressures, or if the soil is heated to high
temperatures using RF heating, the soil will likely require cooling
14
before reestablishment of the microbial population can take
place (U.S. EPA, 1991).
Notice
The U.S. Environmental Protection Agency through its Office of
Research and Development funded the research described
here. It has been subjected to the Agency’s peer and adminis-
trative review and has been approved for publication as an EPA
document. Mention of trade names or commercial products
does not constitute endorsement or recommendation for use.
References
Abdul, A. S., T. L. Gibson, and D. N. Rai, Selection of surfactants
for the removal of petroleum products from shallow sandy
aquifers, Ground Water, 28(6):920-926, 1990.
Aines, R., R. Newmark, W. McConachie, K. Udell, D. Rice, A.
Ramirez, W. Siegel, M. Buettner, W. Daily, P. Krauter, E.
Folsom, A. Boegel, D. Bishop, Dynamic underground strip-
ping project, UCRL-JC-109902, Waste Management Sympo-
sium, Tucson, Arizona, March 1-5, 1992.
Anderson, D. C., K. W. Brown, and J. C. Thomas, Conductivity
of compacted clay soils to water and organic liquids, Waste
Manag. Res., 3:339-349, 1985.
Arthurs, P., W. H. Stiver, and R. G. Zytner, Passive volatilization
of gasoline from soil, J. Soil Contamin., 4(2):123-135, 1995.
Atkins, P. W.,
Physical Chemistry
, Third Edition, W. H. Freeman,
New York, 1986.
Basile, A. J., and G. Smith, Innovative treatment combination
rings bell for AT&T, Hazmat World, 52-53, March 1994.
Baehr, A. L., Selective transport of hydrocarbons in the unsatur-
ated zone due to aqueous and vapor partitioning, Water
Resour. Res., 23(10):1926-1938, 1987.
Bear, J., and A. Gilman, Migration of salts in the unsaturated
zone caused by heating, Trans. Porous Media, 19(2):139-
156, 1995.
Figure 1. Flow Chart to indicate which of the thermal techniques may be applicable for a particular site.
Volatile
Contaminant?
Sandy
Media ?
Unsaturated
Conditions ?
Vacuum
Extraction
Steam or
Hot Air
Injection
Air Sparging
Nonvolatile
Contaminant ?
Sandy
Media ?
Steam or Hot
Air Injection
Hot Water
Injection
Electrical
Heating
Steam
Injection
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Semivolatile
Contaminant ?
Sandy
Media ?
Unsaturated
Conditions ?
Yes
Yes
Yes Yes
or
Electrical
Heating
15
Brown, K. W., and J. C. Thomas, A mechanism by which organic
liquids increase the hydraulic conductivity of compacted clay
materials, Soil Sci. Soc. Am. J., 51:1451-1459, 1987.
Cancela, G. D., E. R. Taboada, and F. Sanchez-Rasero,
Carbendazim adsorption on montmorillonite, peat, and soils,
J. Soil Sci., 43:99-111, 1992.
Davidson, L. B., The effect of temperature on the permeability
ratio of different fluid pairs in two-phase systems, J. Petrol.
Tech., 1037-1046, August 1969.
Davis, E. L., Effect of temperature and pore size on the hydraulic
properties and flow of a hydrocarbon oil in the subsurface, J.
Contamin. Hydrol., 16:55-86, 1994.
Davis, E. L., Steam injection for soil and aquifer remediation,
Ground Water Issue Paper, in preparation, 1997a.
Davis, E. L., Electrical heating of the subsurface for soil and
aquifer remediation, Ground Water Issue Paper, in prepara-
tion, 1997b.
Davis, E. L., Hot water enhanced remediation of soils and
aquifers, Ground Water Issue Paper, in preparation, 1997c.
Davis, E. L., and B. K. Lien, Laboratory study on the use of hot
water to recover light oily wastes from sands, EPA/600/R-93/
021, R. S. Kerr Environmental Research Laboratory, Ada,
Oklahoma, February 1993.
Dev, H., Radio frequency enhanced in-situ decontamination of
soils contaminated with halogenated hydrocarbons, EPA/
600/9-86/022, Land Disposal, Remedial Action, Incineration
and Treatment of Hazardous Wastes, Proceedings of Twelfth
Annual Research Symposium at Cincinnati, Ohio, April 21-23,
1986.
Dev, H., Management Plan: Demonstration testing and evalua-
tion of in situ soil heating, DOE Contract Number DE-AC05-
930R22160, IITRI Project C06787, 1993.
Dev, H., J. Bridges, G. Sresty, J. Enk, N. Mshaiel, and M. Love,
Radio frequency enhanced decontamination of soils contami-
nated with halogenated hydrocarbons, U.S. EPA, Cincinnati,
Ohio, EPA/600/2-89/008, February 1989.
Dewing, H. H., and R. B. Schluter, Characterization and recovery
of mercury from electrical manufacturing wastes by thermal
desorption, U. S. Department of the Interior, Report of Inves-
tigations 9513, 1994.
Edmondson, T. A., Effect of temperature on waterflooding, J.
Can. Petrol. Technol., 236-242, October 1965.
Esposito, P., J. Hessling, B. B. Locke, M. Taylor, M. Szabo, R.
Thumau, C. Rogers, R. Traver, and E. Barth, Results of
treatment evaluations of a contaminated synthetic soil, J. Air
Pollut. Control Assoc., 39:294-304, 1989.
Fares, A., B. Kindt, R. Lapuma, and G. P. Perram, Desorption
kinetics of trichloroethylene from powdered soils, Environ.
Sci. Technol., 29(6):1564-1568, 1995.
Farrington, P., Groundwater Technologies Inc., Norwood, Mass.,
Personal Communication, July 22, 1996.
Feenstra, S., D. M. Mackay, and J. A. Cherry, A method for
assessing residual NAPL based on organic chemical concen-
trations in soil samples, Ground Water Monit. Rev., 128-136,
Spring, 1991.
Fernandez, F., and R. M. Quigley, Viscosity and dielectric
constant controls on the hydraulic conductivity of clayey soils
permeated with water-soluble organics, Can. Geotech. J.,
25:582-589, 1988.
Fulton, D. E., G. J. Reuter, and T. E. Buscheck, Hot water
enhanced recovery of phase separated lubricating oil, Pro-
ceedings of the Petroleum Hydrocarbons and Organic Chemi-
cals in Ground Water: Prevention, Detection, and Restoration
Conference and Exposition, 143-156, November 20-22, 1991.
Gauglitz, P. A., T. M. Bergsman, S. M. Caley, W. O. Heath, M. C.
Miller, R. W. Moss, J. S. Roberts, R. Schalla, M. H. Schlender,
T. R. Jarosch, C. A. Eddy-Dilek, and B. B. Looney, Six-phase
soil heating for enhanced removal of contaminants: Volatile
organic compounds in non-arid soil integrated demonstration,
Savannah River Site, Prepared for the U.S. Office of Technol-
ogy Development, U.S. Department of Energy, Contract DE-
AC-06-76RLO 1830, October 1994.
Gerencher, E. H., D. E. Konasewich, and K. A. Morin,
Hydrogeological investigation of coal tar contamination at a
former coal gasification facility, Subsurface contamination by
immiscible fluids, Balkema Rotterdam, 1992.
Hall, A. L., and R. W. Bowman, Operation and performance of the
Slocum thermal recovery project, J. Petrol. Tech., 402-408,
April 1973.
Harmsen, G. J., Oil recovery by hot-water and steam injection,
Eighth World Petroleum Congress, 3:243-251, 1971.
Hatzinger, P. B., and M. Alexander, Effect of aging chemicals in
soil on their biodegradability and extractability, Environ. Sci.
Technol., 29(2):537-545, 1995.
Herbeck, E. F., R. C. Heintz, and J. R. Hastings, Fundamentals
of tertiary oil recovery Part 8 - Thermal recovery by hot fluid
injection, Petrol. Eng., 24-34, August 1976.
Heron, G., T. H. Christensen, and C. G. Enfield, Temperature
effects on the distribution of organics in soils and groundwater
and implications for thermally enhanced in-situ remediation,
submitted for publication in Environ. Sci. Technol., December
1996.
Ho, C. K., and K. S. Udell, An experimental investigation of air
venting of volatile liquid hydrocarbon mixtures from homoge-
16
neous and heterogeneous porous media, J. Contamin. Hydrol.,
11:291-316, 1992.
Horvath, A. L.,
Halogenated Hydrocarbons
, Marcel Dekker, New
York, 1982.
Huling, S. G., Facilitated transport, Superfund Ground Water
Issue Paper, EPA/540/4-89/003, August 1989.
Hunt, J. R., N. Sitar, and K. S. Udell, Nonaqueous phase liquid
transport and cleanup, 2. Experimental studies, Water Resour.
Res., 24(8):1259-1267, 1988.
Iben, I. E., W. A. Edelstein, R. B. Sheldon, A. P. Shapiro, E. E.
Uzgiris, C. R. Scatena, S. R. Blaha, W. B. Silverstein, G. R.
Brown, G. L. Stegemeier, and H. J. Vinegar, Thermal blanket
for in-situ remediation of surficial contamination: A pilot study,
Environ. Sci. Technol., 30(11):3144-3154, 1996.
Isherwood, W. F., J. Ziagos, E. Nichols, P. Krauter, and D. Rice,
Jr, Enhancing aquifer cleanup with reinjection, National Ground
Water Association Meeting, Houston, Texas, November 4-6,
1992.
Jarosch, T. R., R. J. Beleski, and D. Faust, Final Report: In Situ
Radio Frequency Heating Demonstration, WSRC-TR-93-673,
U. S. Department of Energy Contract No. DE-AC09-
89SR18035, 1994.
Jin, Y., and W. A. Jury, Characterizing the dependence of gas
diffusion coefficient on soil properties, Soil Sci. Soc. Am. J.,
60:66-71, 1996.
Johnson, Jr., L. A., Development of the CROW
TM
Process,
Topical Report, DOE/MC/11076-3847, May 1994.
Johnson, Jr., L. A., and F. D. Guffey, Contained Recovery of Oily
Wastes (CROW), Work performed under Assistance Agree-
ment CR-815333, U. S. EPA, Risk Reduction Engineering
Laboratory, Cincinnati, Ohio, August 1990.
Johnson, P. C., C. C. Stanley, M. W. Kemblowski, D. L. Byers,
and J. D. Colthart, A practical approach to the design, opera-
tion, and monitoring of in situ soil-venting systems, Ground
Water Monit. Rev., 159-178, Spring, 1990.
Jury, W. A., D. Russo, G. Streile, and H. El Abd, Evaluation of
volatilization by organic chemicals residing below the soil
surface, Water Resour. Res., 26(1):13-20, 1990.
Karickhoff, S. W., D. S. Brown, and T. A. Scott, Sorption of
hydrophobic pollutants on natural sediments, Water Res.,
13:241-248, 1979.
Kemper, W. D., Movement of water as effected by free energy
and pressure gradients: I. Application of classic equations for
viscous and diffusive movements to the liquid phase in finely
porous media, Soil Sci. Soc. Am. Proc., 25(4):255-260, 1961a.
Kemper, W. D., Movement of water as affected by free energy
and pressure gradients: II. Experimental analysis of porous
systems in which free energy and pressure gradients act in
opposite directions, Soil Sci. Soc. Am. Proc., 25(4):260-265,
1961b.
Keyes, B. R., and G. D. Silcox, Fundamental study of the thermal
desorption of toluene from montmorillonite clay particles,
Environ. Sci. Technol., 28:840-849, 1994.
Lide, D. R., ed.,
CRC Handbook of Chemistry and Physics
, 74th
Edition, CRC Press, Boca Raton, 1993.
Lighty, J. S., D. W. Persing, V. A. Cundy, and D. G. Linz,
Characterization of thermal desorption phenomena for the
cleanup of contaminated soil, Nucl. Chem. Waste Manage.,
8:225-237, 1988.
Lighty, J. S., G. D. Silcox, D. W. Persing, V. A. Cundy, and D. G.
Linz, Fundamentals for the thermal remediation of contami-
nated soils. Particle and bed desorption models, Environ. Sci.
Technol., 24(5):750-757, 1990.
Lingineni, S., and V. K. Dhir, An experimental and theoretical
study of remediation of multicomponent organic contaminants
in the unsaturated soil by venting, Fundamentals of Heat
Transfer in Porous Media, HTD-VOl. 193, ASME, 99-107,
1992.
Lyman, W. J., P. J. Reidy, and B. Levy, Assessing UST correc-
tive action technology, A scientific evaluation of the mobility
and degradability of organic contaminants in the subsurface
environments, U.S. EPA Report, EPA/600/2-91/053, Septem-
ber 1991.
Mackay, D. M., and J. A Cherry, Groundwater contamination:
Pump-and-Treat remediation, Environ. Sci. Technol.,
23(6):630-636, 1989.
Mackay, D. M., and W. J. Shiu, Critical review of Henry’s law
constants for chemicals of environmental interest, J. Phys.
Chem. Ref. Data, 10(4):1175-1199, 1981.
Marley, M. C., R. S. Kasevich, and S. L. Price, Enhancing site
remediation through radio frequency heating, AIChE Annual
Meeting, St. Louis, Missouri, November 7-12, 1993.
Miller, M. M., S. P. Wasik, G.-L. Huang, W.-Y. Shiu, and D.
Mackay, Relationship between octanol-water partition coeffi-
cient and aqueous solubility, Environ. Sci. Technol., 19(6):522-
529, 1985.
Millington, R. J., Gas diffusion in porous media, Science, 130:100-
102, 1959.
Mungan, N., Role of wettability and interfacial tension in water
flooding, Soc. Petrol. Eng. J., 115-123, June 1964.
17
Mungan, N., Interfacial effects in immiscible liquid-liquid dis-
placement in porous media, Soc. Petrol. Eng. J., 217-253,
1966.
Newell, C., S. D. Acree, R. R. Ross and S. G. Huling, Light
nonaqueous phase liquids, Ground Water Issue Paper, EPA/
540/S-95/500, July 1995.
Newmark, R. L., and R. D. Aines, Summary of the LLNL gasoline
spill demonstration - Dynamic Underground Stripping Project,
Lawrence Livermore National Laboratory, Berkeley Environ-
mental Restoration Center, UCRL-ID-120416, April 3, 1995.
Ong, S. K., T. B. Culver, L. W. Lion, and C. A. Shoemaker, Effects
of soil moisture and physical-chemical properties of organic
pollutants on vapor-phase transport in the vadose zone, J.
Contamin. Hydrol., 11:273-290, 1992.
Perry, R. H., and C. H. Chilton, Chemical Engineers’ Handbook,
5th ed., McGraw-Hill, New York, 1973.
Peters, R. W., C. D. Montemango, L. Shem, and B. G. Lewis,
Surfactant Flooding of Diesel-Fuel-Contaminated Soil, ANL\
CP—73805, 1991.
Piatt, J. J., D. A. Backhus, P. D. Capel, and S. J. Eisenreich,
Temperature-dependent sorption of naphthalene, phenan-
threne, and pyrene to low organic carbon aquifer sediments,
Environ. Sci. Technol., 30(3):751-760, 1996.
Porter, L. K., W. D. Kemper, R. D. Jackson, and B. A. Stewart,
Chloride diffusion in soils as influenced by moisture content,
Soil Sci. Soc. Am. Proc., 24:460-463, 1960.
Poston, S. W., S. Ysrael, A. K. M. S. Hossain, E. F. Montgomery,
and H. J. Ramey, Jr., The effect of temperature on irreducible
water saturation and relative permeability of unconsolidated
sands, Trans. Soc. Petrol. Eng., 249:171-180, 1970.
Ramey Jr., H. J., A current review of oil recovery by steam
injection, Seventh World Petroleum Congress Proceedings,
3:471-476, 1967.
Roberts, P. V., J. Schreiner, and G. D. Hopkins, Field study of
organic water quality changes during groundwater recharge in
the Palo Alto Baylands, Water Res., 16:1025-1035, 1982.
Ryan, J. A., R. M. Bell, J. M. Davidson, and G. A. O’Connor, Plant
uptake of non-ionic organic chemicals from soils, Chemo-
sphere, 17(12):2299-2323, 1988.
Sanders, P. F., Calculation of soil cleanup criteria for volatile
organic compounds as controlled by the soil-to-groundwater
pathway: Comparison of four unsaturated soil zone leaching
models, J. Soil Contamin., 4(1):1-24, 1995.
Schwarzenbach, R. P., and J. Westall, Transport of nonpolar
organic compounds from surface waters to groundwater.
Laboratory sorption studies, Environ. Sci. Technol., 15:1360-
1367, 1981.
Shah, F. H., H. A. Hadim, and G. P. Korfiatis, Laboratory studies
of air stripping of VOC-contaminated soils, J. Soil Contamin.,
4(1):93-109, 1995.
Sresty, G. C., Treatability study work plan, Demonstration test-
ing and evaluation of in situ soil heating, U. S. DOE Contract
DE-AC05-930R22160, December 30, 1994.
Stephenson, R. M., Mutual solubilities: Water-ketones, water-
ethers, and water-gasoline-alcohols, J. Chem. Eng. Data,
37:80-95, 1992.
Stewart, L. D., and K. S. Udell, Mechanism of residual oil
displacement by steam injection, SPE Reservoir Engineering,
1233-1242, November 1988.
Swanstrom, C. P., and M. Besmer, Bench- and pilot-scale
thermal desorption treatability studies on pesticide-contami-
nated soils from Rocky Mountain Arsenal, Presented at Sev-
enth Annual Gulf Coast Environmental Conference, Houston,
Texas, March 9, 1995.
Thoma, G. J., G. Hildebrandt, K. T. Valsaraj, L. J. Thibodeaux,
and C. Springer, Transport of chemical vapors through soil: A
landfill cover simulation experiment, J. Hazard. Mat., 30:333-
342, 1992.
Tognotti, L., M. Flytzani-Stephanopoulos, A. F. Sarofim, H.
Kopsinis, and M. Stoukides, Study of adsorption-desorption of
contaminants on single soil particles using the electrodynamic
thermogravimetric analyzer, Environ. Sci. Technol., 25(1):104-
109, 1991.
Treybal, R. E.,
Mass-Transfer Operations
, 3rd. ed., McGraw-Hill,
New York, 1980.
Tyn, M. T., and W. F. Calus, Temperature and concentration
dependence of mutual diffusion coefficients of some binary
liquid systems, J. Chem. Eng. Data, 20(3):310-316, 1975.
Udell, K. S., and L. D. Stewart, Jr., Field study of in situ steam
injection and vacuum extraction for recovery of volatile or-
ganic solvents, Dept. of Mechanical Engineering, University of
California, June 1989.
U.S. Environmental Protection Agency, Toxic Treatments, In
situ steam/hot-air stripping technology, Applications Analysis
Report, EPA/540/A5-90/008, Risk Reduction Engineering
Laboratory, Cincinnati, Ohio, March 1991.
U.S. Environmental Protection Agency, SITE Technology Cap-
sule, KAI radio frequency heating technology, EPA 540/R-94/
528a, Cincinnati, Ohio, 1995a.
U.S. Environmental Protection Agency, IITRI radio frequency
heating technology, Innovative Technology Evaluation Re-
port, EPA/540/R-94/527, June 1995b.
U.S. Environmental Protection Agency, Low temperature ther-
mal aeration (LTTA) process Canonie Environmental Ser-
vices, Inc., Applications Analysis Report, EPA/540/AR-93/
504, July 1995c.
18
U.S. Environmental Protection Agency, In situ steam enhanced
recovery process, Hughes Environmental Systems, Inc., In-
novative Technology Evaluation Report, EPA/540/R-94/510,
July 1995d.
Uzgiris, E. E., W. A. Edelstein, H. R. Philipp, and I. E. T. Iben,
Complex thermal desorption of PCBs from soil, Chemo-
sphere, 30(2):377-387,1995.
Valsaraj, K. T., On the physico-chemical aspects of partitioning
of non-polar hydrophobic organics at the air-water interface,
Chemosphere, 17(5):875-887, 1988.
Vaughan P. J., K. S. Udell, and M. J. Wilt, The effects of steam
injection on the electrical conductivity of an unconsolidated
sand saturated with a salt solution, J. Geophys. Res.,
98(B1):509-518, 1993.
Verschueren, K.,
Handbook of Environmental Data on Organic
Chemicals,
2nd ed., Van Nostrand Reinhold, New York, 1983.
Villaume, J. F., P. C. Lowe, and D. F. Unites, Recovery of coal
gasification wastes: An innovative approach, Proceedings of
the Third National Symposium on Aquifer Restoration and
Ground-Water Monitoring, OCLC #9983271, 434-445, 1983.
Vogel, J. V., Gravity drainage vital factor for understanding
steam floods, Oil Gas J., 90(48):42-47, 1992.
Weber, W. J., Jr., T. C. Voice, M. Pirbazari, G. E. Hunt, and D. M.
Ulanoff, Sorption of hydrophobic compounds by sediments,
soils and suspended solids - II. Sorbent evaluation studies,
Water Res., 17(10):1443-1452, 1983.
Weber, W. J., Jr., P. M. McGinley, and L. E. Katz, Sorption
phenomena in subsurface systems: Concepts, models and
effects on contaminant fate and transport, Water Res., 25:499-
528, 1991.
Willman, B. T., V. Valleroy, G. Runberg, A. Cornelius, L. Powers,
Laboratory studies of oil recovery by steam injection, Petrol.
Trans., AIME, July 1961.
Wilson, D. J., A. N. Clarke, and J. H. Clarke, Soil clean up by in-
situ aeration. I. Mathematical modeling, Separation Sci.
Technol., 23(10&11):991-1037, 1988.
Yalkowsky, S. H., and S. Banerjee,
Aqueous Solubility Methods
of Estimation for Organic Compounds
, Marcel Dekker, New
York, 1992.
Yow, J. L., R. D. Aines, and R. L. Newmark, Demolishing NAPLs,
Civil Eng., 65(8):57-59, August 1995.