Flood® SWF-SOLID - Solid Color Wood Finish

Flood

SWF-SOLID

Solid Color Wood Finish

Specification Guidelines

MANUFACTURER

Akzo Nobel Paints LLC

15885 West Sprague Road

Strongsville, OH 44136

Phone: 1-800-321-3444

Fax: 1-440-297-8908

www.flood.com

PRODUCT DESCRIPTION

Flood

SWF-SOLID Color Wood Finish is a premium finish for new wood

and for recoating old applications. SWF-SOLID is fortified with E-B

Emulsa-Bond

to provide unsurpassed adhesion to vertical and horizontal

exterior substrates where other products ultimately fail or require

extensive preparation and priming. SWF-SOLID blends acrylic and urethane

technologies to provide reliable adhesion, abrasion-resistance and

flexibility. SWF-SOLID delivers high traffic performance on deck surfaces

and is the perfect choice for long-lasting beauty on siding. SWF-SOLID is

guaranteed not to peel or blister (see reverse for limited warranty details.)

BASIC USES

• For exterior use only

• New or weathered exterior wood

• Previously coated exterior surfaces

• Siding (new or weathered, including: untreated solid wood, primed

and previously finished fiber cement board and plywood, including T1-11,

and aluminium)

• Decks, docks and other horizontal surfaces including PTW, cedar,

redwood, hardwoods and composite decking

• Fences and other vertical surfaces

• Trim boards and outdoor wood furniture

• Weathered vertical masonry including stucco, painted block, EIFS, etc.

TECHNICAL DATA

FINISH: Flat: < 10% @ 60º

COLORS: Available in 3 tint bases (tintable to 96 colors)

True White - ready mix formula

VEHICLE TYPE: Alkyd, acrylic/urethane blend

VISCOSITY: 74-84 KU

VOC: Does not ex ceed 250 g/L (2.1 lb/gal). SCAQMD compliant:

does not exceed 100 g/L (0.83 lbs/gal); use as is, do not thin.

% WEIGHT SOLIDS:

True White: 51.85 +/- 1%

Pastel Base: 48.74 +/- 1%

Mid Tone Base: 46.76 +/- 1%

Deep Base: 44.20 +/- 1%

% VOLUME SOLIDS:

True White: 37.96 +/- 1%

Pastel Base: 36.10 +/- 1%

Mid Tone Base: 35.77 +/- 1%

Deep Base: 34.98 +/- 1%

DENSITY (LBS.GAL):

True White: 10.61 +/- 1%

Pastel Base: 9.96 +/- 1%

Mid Tone Base: 9.59 +/- 1%

Deep Base: 9.26 +/- 1%

FLASH POINT: >180ºF

CONTAINER SIZE: 1-gallon and 5-gallon

DRY TIME: At 70º F (25º C) and 50% relative humidity

To touch: 1-2 hours, depending on temperature and humidity

To recoat: 3-4 hours, depending on temperature and humidity

NOTE: Product finish dry/cure times may be prolonged when

low temperature and/or high humidity levels exist.

FREEZE/THAW: Passes 3 cycles

SURFACE PREPARATION

GENERAL DIRECTIONS:

1. Surfaces to be coated should be clean and dry before applying

SWF-SOLID Solid Color Wood Finish.

2. Sand, scrape or wire brush to remove all loose flaking or peeling finish

3. Pressure wash to remove excess dirt, chalk, oxidation and other

surface contamination.

4. Mildew - A mildew-resisting component has been incorporated into

this product to make its dry film mildew resistant, however, no coating

is mildew proof. Before coating, remove mildew by scrubbing the

surface with a mixture of four ounces of non-ammonia detergent

(TSP), one quart of household bleach and three quarts of water.

Allow this solution to remain on the surface for 10-15 minutes, then

rinse thoroughly. Repeat until mildew is completely removed. Wear

protective glasses or goggles and waterproof gloves when using this

solution. Quickly wash off mixture that touches your skin. Allow 2-3

days dry time after cleaning before finishing or when wood has a

moisture content of <15%.

NEW WOOD SURFACES:

The ideal time to finish new wood is one to three months after

installation. Many new wood surfaces can have a hard, shiny condition

called mill glaze that prevents maximum penetration and adhesion

of a finish. All new wood, especially decks, should be prepared with

Flood Wood Stripper or FloodPro

Stripper/Cleaner to reduce mill glaze,

remove natural wood chemicals and other factory applied sealers to

open wood and allow maximum penetration.

WEATHERED WOOD OR PREVIOUSLY COATED SURFACES:

Follow "General Directions" for surface prep.

HIGH EXTRACTIVE WOODS: (i.e. red cedar, redwood)

"Extractives" or tannins are natural wood chemicals that give

wood its color. These chemicals can "bleed" into a topcoat and

cause discoloration of the finish. Use Flood Wood Cleaner or Flood

Dekswood

(diluted with water from 1:1 for redwood to 4:1 for

cedar) to remove tannin stains and clean the surface prior to coating.

To prevent tannin bleed, use an oil-based exterior stain blocking

primer, designed to seal exterior wood to control tannin and knot

bleeding, prior to application. Alternatively, apply the first coat of

Flood SWF-SOLID Wood Finish. Allow the first coat to cure 7 days

prior to application of the second coat.

continued on reverse side

*See reverse side for limited warranty details.

LEAD STATEMENT

WARNING! If you scrape, sand, or remove old paint, you may

release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN

CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN

CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.

Wear a NIOSH-approved respirator to control lead exposure. Clean

up carefully with a HEPA vacuum and a wet mop. Before you start,

find out how to protect yourself and your family by contacting

the National Lead Information Hotline at 1-800-424-LEAD or log

on to www.epa.gov/lead.

COLOR SELECTION

• Before starting job, test your color choice on a small area

• Buy sufficient product for the whole job and box or intermix all

product together before staining to avoid color variance

• DO NOT USE TINT BASES UNTINTED

NOTE: Custom tint using colorants that are approved for exterior use only.

APPLICATION TOOLS

• Apply FloodPro Solid Color Finish with a synthetic brush, 3/8" - 3/4"

nap, tight knit synthetic roller cover, stain brush/pad or airless sprayer

• Spray equipment .015 - .019 fluid tip/1,500-2,100 psi fluid pressure

APPLICATION

CAUTION: Surfaces are slippery when wet. Use caution when

walking on wet surfaces during application.

1. Clean as directed under "Surface Preparation".

2. Cover everything you do not wish to coat including plants and shrubs.

3. Apply between 50º and 80º F. Do not apply in direct sunlight, on hot

surfaces or if cold and/or wet weather is expected within 48 hours.

4. Mix product thoroughly before and during application. Do not thin.

5. For color uniformity, use a larger container (ex. 5 gallon bucket) to

intermix all product to be used in one area.

6. Apply an even coat of SWF-SOLID Color Wood Finish avoiding

heavy application.

7. Always work the entire length of a deck board or horizontal siding to

a logical break, such as a window or door frame.

8. Vertical siding should be coated from top to bottom.

9. If spraying on product, always back brush or back roll material

to provide maximum substrate coverage, penetration and

uniform appearance.

10. If additional coats are required, it may be applied 3-4 hours after

initial application.

COVERAGE RATES

• Smooth/moderately porous surfaces: 350 - 400 sq. ft/gal

• Rough/weathered/porous surfaces: 250 - 350 sq. ft/gal

NOTE: Actual coverage rates may vary depending upon substrate type

and/or conditions as well as application method.

MAINTAINING SWF-SOLID COLOR FINISH

Surfaces with harsh exposure to sun, weather or foot traffic will show

wear more quickly than other areas - if this happens, clean affected areas

and recoat as necessary.

CLEANUP & STORAGE

• Cleanup with soap and water.

• If SWF-SOLID is allowed to dry on tools, remove with

paint remover.

• Store unused portion in a sealed container to prevent gelling.

• KEEP FROM FREEZING

DANGER: Rags, steel wool or waste soaked with this

product may spon ta ne ous ly catch fire if improperly

discarded. Immediately after use, place rags, steel

wool or waste in a sealed, water filled metal container.

LIMITED WARRANTY

Akzo Nobel Paints LLC warrants SWF-SOLID against peeling and blistering

for fifteen (15) years on siding and five (5) years on decks from the date of

purchase if applied according to label instructions to a properly prepared

surface. If SWF-SOLID fails to perform as described above, Akzo Nobel

Paints LLC will, at its option, provide an equivalent amount of new product

at no charge or refund the purchase price. This warranty does not include

labor or the cost of application of any product, and in no event shall Akzo

Nobel Paints LLC be responsible for damages in excess of the purchase

price. Claims must be made in writing and accompanied by proof of

purchase. This warranty does not apply to problems caused by alteration of

this product, accident, misuse, improper storage, abuse, or neglect. THERE

ARE NO OTHER EXPRESS WARRANTIES. IN NO EVENT SHALL AKZO NOBEL

PAINTS LLC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING FROM ANY BREACH OF THIS WARRANTY OR ANY IMPLIED

WARRANTY OF MERCHANTABILITY AND FITNESS FOR USE. Some states

do not allow the exclusion or limitation of incidental or consequential

damages so the above limitation may not apply to you. This warranty gives

you specific legal rights and you may have other rights which may vary

from state to state.

WARNING! COMBUSTIBLE LIQUID AND VAPOR. CONTAINS

PETROLEUM DISTILLATES. VAPOR HARMFUL. MAY AFFECT THE

BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR

NAUSEA. MAY CAUSE EYE, SKIN, NOSE AND THROAT IRRITATION.

NOTICE: Reports have associated repeated and prolonged occupational

overexposure to solvents with permanent brain and nervous system damage.

Intentional misuse by deliberately concentrating and inhaling the contents

may be harmful or fatal. Use only with adequate ventilation. For

exterior use only. Always wear appropriate eye protection and protective

clothing. Avoid breathing vapors or spray mist. If spray applying, follow

spray equipment manufacturer’s recommendations. For additional protection,

wear an appropriate NIOSH/MSHA respirator, follow manufacturer’s directions

carefully. Close container after each use. Avoid contact with eyes, skin and

clothing. Wash thoroughly after handling. FIRST AID: In case of eye contact,

flush immediately with plenty of water, especially under the lids, for at least

15 minutes and get medical attention; for skin wash thoroughly with soap

and water. If you experience difficulty in breathing, leave area to obtain fresh

air. If continued difficulty is experienced, get medical assistance immediately.

If swallowed, do not induce vomiting, get medical attention immediately. In

case of spillage, absorb with inert material and dispose of in accordance with

local regulations. KEEP OUT OF THE REACH OF CHILDREN.

Flood

SWF-SOLID

Solid Color Wood Finish

For additional information or assistance,

write or call toll-free: 1-800-321-3444.

Akzo Nobel Paints LLC

15885 Sprague Road | Strongsville, OH 44136

www.flood.com

® indicates a registered trademark of the AkzoNobel

group of companies. Reorder #M12097 - 2/10