CHILD SAFETY DEVICES
FITTING INSTRUCTIONS
FACE FIX - RH180/CLR
1. Ensure length of operating chain
is in compliance with BS EN13120*.
Position device at max distance
possible from the control mechanism.
Mark hole positions on substrate.
2. Drill pilot hole and screw device
into position. Use applicable wall
plugs if required.
2. Drill pilot hole and screw device
into position. Use applicable wall
plugs if required.
3. Ensure the distance between the
two strands of the loop is not
more than 50mm at the point of
exit from the device.
RECESS FIT - RH181/CLR
3. Ensure the distance between the
two strands of the loop is not
more than 50mm at the point of
exit from the device.
* For a full overview of the requirements of BS EN13120, please refer to the relevant product Child Safety Guide.
All the above components are tested to ensure compliance with the Child Safety requirements of BS EN13120.
Using any alternative components would not be covered by our certification and require additional testing to ensure compliance.
Make sure the required labels are left on the device & blind when installation is complete.
1. Ensure length of operating chain
is in compliance with BS EN13120*.
Position device at max distance
possible from the control mechanism.
Mark hole position on substrate.
.
.
CHILD SAFE
PRODUCT
.
.
ECLIPSE BLIND SYSTEMS INCHINNAN BUSINESS PARK RENFREW PA4 9RE SCOTLAND UK
TEL: +44 (0) 141 812 3322 FAX: +44 (0) 141 812 5253 www.eclipseblinds.co.uk
© Eclipse 2014 MSM4304
CONTROL CHAIN SAFETY CLIP - LH892 (LARGE)
1. Ensure length of operating chain
is in compliance with BS EN13120*.
Position device at max distance
possible from the control mechanism.
Mark hole positions on substrate.
3. Ensure the distance between the
two strands of the loop is not
more than 50mm at the point of
exit from the device.
* For a full overview of the requirements of BS EN13120, please refer to the relevant product Child Safety Guide.
CONTROL CHAIN SAFETY CLIP - LH891 (SMALL)
2. Drill pilot holes and screw device
into position. Use applicable wall
plugs if required.
3. Ensure the distance between the
two strands of the loop is not
more than 50mm at the point of
exit from the device.
1. Ensure length of operating chain
is in compliance with BS EN13120*.
Position device at max distance
possible from the control mechanism.
Mark hole position on substrate.
.
.
CHILD SAFE
PRODUCT
.
.
CHILD SAFETY DEVICES
FITTING INSTRUCTIONS
2. Drill pilot hole and screw device
into position. Use applicable wall
plugs if required.
ECLIPSE BLIND SYSTEMS INCHINNAN BUSINESS PARK RENFREW PA4 9RE SCOTLAND UK
TEL: +44 (0) 141 812 3322 FAX: +44 (0) 141 812 5253 www.eclipseblinds.co.uk
All the above components are tested to ensure compliance with the Child Safety requirements of BS EN13120.
Using any alternative components would not be covered by our certification and require additional testing to ensure compliance.
Make sure the required labels are left on the device & blind when installation is complete.
© Eclipse 2014 MSM4305
All the above components are tested to ensure compliance with the Child Safety requirements of BS EN13120.
Using any alternative components would not be covered by our certification and require additional testing to ensure compliance.
Make sure the required labels are left on the device & blind when installation is complete.
* For a full overview of the requirements of BS EN13120, please refer to the relevant product Child Safety Guide.
CORD CLEAT - VH140
3. Ensure complete length of pull
cords can be accumulated and
maintained when the internal
blind is in the fully retracted
position.
1. Position device as close to the
headrail as possible and in all
cases, no less than 1.5m from
the floor in compliance with
BS EN13120*. Mark hole
positions on substrate.
ECLIPSE BLIND SYSTEMS INCHINNAN BUSINESS PARK RENFREW PA4 9RE SCOTLAND UK
TEL: +44 (0) 141 812 3322 FAX: +44 (0) 141 812 5253 www.eclipseblinds.co.uk
.
.
CHILD SAFE
PRODUCT
.
.
CHILD SAFETY DEVICES
FITTING INSTRUCTIONS
2. Drill pilot holes and screw device
into position. Use applicable wall
plugs if required.
© Eclipse 2014 MSM4306
ROMAN REAR CORD BREAKAWAY - RH471
4. Tie the cord off at the bottom.
Repeat for each column.
1. Should your safety devices
breakaway do not try to operate
the blind.
2. For smaller blinds, simply reconnect
the breakaway components. For
larger blinds remove the blind from
the brackets and reconnect the
breakaways.
3. Rehang the blind as per the fitting
instructions if required and ensure
the blind is level and operating
correctly.
2. Apply the Roman Rear Cord
Breakaway Connector to the tapes
on the back of the blind. N.B. Use
one device at each point where the cord
passes the tapes on the back of the blind.
1. Sew tube tape at bottom along
panel & insert support rod. For
recommended number of panels
refer to Tech Spec TS037.
ECLIPSE BLIND SYSTEMS INCHINNAN BUSINESS PARK RENFREW PA4 9RE SCOTLAND UK
TEL: +44 (0) 141 812 3322 FAX: +44 (0) 141 812 5253 www.eclipseblinds.co.uk
.
.
CHILD SAFE
PRODUCT
.
.
CHILD SAFETY DEVICES
FITTING INSTRUCTIONS
REASSEMBLY INSTRUCTIONS
3. Thread the cord through each
of the Roman Rear Cord Breakaway
Connectors on each column.
© Eclipse 2014 MSM4308
All the above components are tested to ensure compliance with the Child Safety requirements of BS EN13120. For a full overview of the requirements of BS EN13120,
please refer to the relevant product Child Safety Guide. Using any alternative components would not be covered by our certification and require additional testing to
ensure compliance. Make sure the required labels are left on the device & blind when installation is complete.
1
2
